CASETA FAN CONTROL HOW TO

So my voice commands are going through the manufacturers app, but I can still set up any smartthings automations I want for the same device. In my case, I generally find that the manufacturerвЂ™s skill often has options that smartthings doesnвЂ™t offer, So I typically use the manufacturerвЂ™s skill with Alexa and simply donвЂ™t authorize those devices in my smartthings app for use by the SmartThings/Alexa integration.

CASETA FAN CONTROL HOW TO

People have different philosophies on how to handle the duplicate entries. So it doesnвЂ™t matter what devices are in the scenes from AlexaвЂ™s point of view. Alexa doesnвЂ™t actually do anything with the scenes at all, it just passes the request over to smartthings. Good question! Fortunately, It will work just fine. Or will there be a disconnect when Alexa tries to activate a scene that changes the state of a device that she canвЂ™t вЂњseeвЂќ? If I remove the ST-mapped version of the switches from Alexa, but I keep the ST-mapped scenes that I define for those switches, will all of that still process just fine on the ST hub? Is there a known best-practices for managing that? (other than not to use the Lutron skill at all ) Once via ST integration and a second time via the direct Lutron integration. It does NOT allow for any ST-based automation or routines, obviously.Д«iggest downside: Alexa now has all of my light switches twice. This setup also allows the fan to be used via the wall switch or any other Lutron Pico remotes around the room, so as to be intuitive for guests. set living room fan to low ( /medium / high) (aliases to settings 1, 2, and 4).set living room fan to 1 (or 2 / 3 / 4).Today I connected Alexa directly to the Lutron hub, and the fan control works fine through voice control. So ST imports the Lutron switch, then I only tell Alexa about the ST hub and donвЂ™t tell her anything about the Lutron hub. IвЂ™ve previously been using the Lutron light switches in Alexa by way of the ST integration. It does not reliably work when the light is turned on via the pull cord on the fan, but if the light is off it works for the fan as one would expect.ДЄs JDRoberts warned, the fan control does not get imported from the Lutron App into ST. I have the Caseta fan controller installed in the wall now, in place of the dimmer that was (incorrectly) there previously. There donвЂ™t seem to be Caseta connected ones, though, and I donвЂ™t know how to make the Caseta Picos control something that isnвЂ™t Caseta.ДЄny tips on what I should be looking for? I know there are tiny Zwave switch modules that you can embed places, and maybe if there are both dimmer and fan-control versions I could put one of each into the ceiling fan and use that to separate the control of fan vs light.

IвЂ™d replace the dimmer with a fan controller switch and take the bulb out of the light fixture.

If I give up on the nice-to-haves, this should be easy. (f) work with the Caseta infrastructure so that I can continue to have Picos on the wall that people can use to turn on/off the light and possibly the fan (e) be able to use the light in the fan, preferably dimmable, independent from the fan (d) being able to use the light is NOT a must-have В© allow guests to use intuitive switches for everything that is functional (ie, a light cannot be controlled app-only) (a) be able to use the ceiling fan at multiple speeds As things stand right now, that means the fan has to be permanently turned off via the pull cord to avoid dimmer/fan damage. The light and fan only have a single connection wired to the switches, not separate load wires for each.

My problem area is the living room ceiling fan & light, which are currently connected to a Caseta dimmer originally in a 4-way wiring scheme (now with a single Caseta switch and 3 Picos). IвЂ™ve just moved into a new house, and the light switches everywhere are Lutron Caseta switches which are now integrated into my SmartThings hub.